| |
DIAMOND
MOUNTED POINTS
(Electroplated) |
Available in Coarse diamonds, and
Fine Diamonds. Coarse diamonds are used for soft stone; fine diamonds
are used for hard stone. |
PART
# |
SHAFT
SIZE |
POINT
WIDTH |
POINT
HEIGHT |
PHOTO |
A-2 |
1/4" |
3/8" |
1/2" |
|
A-3 |
1/4" |
3/8" |
1" |
|
A-3S |
1/4" |
3/8" |
1" |
|
A-3R |
1/4" |
9/32" |
1" |
|
A-5 |
1/4" |
5/16" |
7/16" |
|
A-15 |
1/8" |
1/8" |
3/8" |
|
A-24 |
1/8" |
1/8" |
5/16" |
|
A-25 |
1/4" |
3/8" |
3/8" |
|
A-26 |
1/4", 1/8" |
1/4" |
1/4" |
|
A-36 |
1/4" |
5/8" |
1/8" |
|
A-40 |
1/4" |
5/16" |
5/16" |
|
A-46 |
1/4" |
7/16" |
13/16" |
|
A-47 |
1/4" |
1/2" |
13/16" |
|
A-48 |
1/4" |
1" |
32/37" |
|
A-52 |
1/8" |
1/8" |
1/8" |
|
A-53 |
1/4" |
5/8" |
5/8" |
|
A-54 |
1/4" |
13/32" |
1 5/8" |
|
A-55 |
1/4" |
1/2" |
1 1/8" |
|
A-56 |
1/4" |
1/2" (Fine)
5/8" (Coarse) |
1" |
(Coarse not shown) |
A-57 |
1/8" |
1/8" |
3/8" |
|
| VCR001 |
1/4" |
2" Brazed Wheel, Fine |
2.5mm |
 |
| HK001 |
1/4" |
2" Brazed Wheel, Coarse |
2.5mm |
| VCR002 |
1/4" |
1 1/2" Brazed Wheel, Fine |
|
|
| HK002 |
1/4" |
1 1/2" Brazed Wheel, Coarse |
| VCR004 |
1/4" |
1" Brazed Wheel, Fine |
|
 |
| HK004 |
1/4" |
1" Brazed Wheel, Coarse |
| VCR009 |
1/4" |
1" Brazed Knife Router, Fine |
|
 |
| VCR021 |
1/4" |
15mm Brazed Bullet, Fine |
28mm |
 |
| HKDA47 |
1/4" |
1/2" Cylinder, Fine |
|
 |
| HKCA12 |
1/4" |
1/2" Cone, Fine |
|
 |
| HKA500 |
1/4" |
1/2" Ball, Fine |
|
 |
#20085 |
1/8" |
.3 mm (Thickness) |
1" (Diameter) |
|
| #43223 |
1/8" |
|
|
Mandrel |
#763660-6 |
|
|
|
1/4" - 1/8" reducer |
| |
|
|
|
|
DIAMOND MOUNTED WHEELS & POINTS
(Metal Bonded ) , 2" Shaft Length |
PART # |
SHAFT SIZE |
POINT WIDTH |
POINT HEIGHT |
PHOTO |
A3 |
1/4" |
7/16" Bullet |
1" |
|
1125 |
1/8" |
1" Wheel |
1/8" |
|
1250 |
1/4" |
1" Wheel |
1/4" |
|
2125 |
1/4" |
2" Wheel |
1/8" |
|
2250 |
1/4" |
2" Wheel |
1/4" |
|
Back to Top
|
SILICON
CARBIDE MOUNTED POINTS
|
|
ITEM
# |
SIZE |
DESCRIPTION |
SHAFT
SIZE |
GRIT |
PHOTO |
|
A-3 |
2 3/4" |
Large, Tapered |
1/4" |
C36 |
|
|
W216 |
1" |
|
1/8" |
C80 |
|
1/4" |
C120 |
1/8" |
C220 |
1/8" |
C320 |
|
A-4 |
1 3/8" |
Large, Tapered |
1/4" |
C120 |
|
|
A-13 |
1 3/16" |
Point |
1/4" |
C120 |
|
|
A-21 |
1 1/16" |
Round Nose |
1/4" |
C120 |
|
A-25 |
1 1/16" |
Ball |
1/4" |
C120 |
|
W-205 |
3/4" |
Drum |
1/4" |
C120
C180 |
|
|
W-221 |
1" |
Drum |
1/4" |
C180 |
|
Back to Top
#30980 Flex Shaft c/w handpiece
|
• 4 ft. long, heavy-duty rubber
covered flex shaft for use
with both die grinder or
router motor
• Ball bearing construction
• 1/4" collet for 1/4" shank
mounted bits
• Speed range 7,500 to
30,000 RPM (Not for use
on tools running less than
7,500 RPM)
|
|
Back to Top
|
1/4"
AIR DIE GRINDERS
|
|
• Rear Exhaust |
ANGLE DIE
GRINDER
• 20,000 RPM, 90 PSI, 4 CFM |
Back to Top
|
|
